Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Arleta?
Gate repair in Arleta typically costs $195 to $850 for most residential jobs, with simple fixes like a remote, a sensor or a worn roller landing near the bottom of that range and operator or control board work landing near the top. A full operator replacement on a residential driveway gate usually runs $750 to $1,900 installed, and commercial systems (FAAC, BFT, DoorKing) price higher because the parts are heavier and the troubleshooting takes longer. The written estimate sets the final price, and the estimate itself is free.
Call (855) 473-3106 to get that estimate scheduled. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday.
Key Takeaways
- Most residential gate repairs in Arleta fall between $195 and $850.
- Operator replacement runs roughly $750 to $1,900 depending on the brand and gate weight.
- Electric gate repair is our core work, not a side service. We treat the motor, control board, wiring and operator as one system.
- We service nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. We identify your system from the operator itself, not from trial and error.
- Estimates are free and every price is set per job.
Gate Repair Cost Breakdown (2026)
These are typical estimated ranges for the Arleta market in 2026. Actual pricing depends on the system on your property, the condition of the gate, and how much labor the diagnosis turns up. The table below covers the work we see most often.
| Repair type | Typical estimated range |
|---|---|
| Remote or keypad programming, transmitter replacement | $85 – $225 |
| Safety sensor / photo-eye adjustment or replacement | $145 – $325 |
| Gate hinge, roller or track realignment | $195 – $450 |
| Control board replacement | $325 – $750 |
| Motor or drive assembly repair (residential) | $395 – $850 |
| Wiring repair, low-voltage or power feed | $225 – $675 |
| Residential operator replacement, installed (Mighty Mule, Ghost Controls, Linear) | $750 – $1,400 |
| Heavy-duty or commercial operator replacement (FAAC, BFT, DoorKing) | $1,200 – $2,800 and up |
| New gate installation, automated | Quoted per job after an on-site estimate |
What pushes a job toward the top of a range: an operator that’s more than a decade old and has sat in the sun every day, a gate that’s out of plum and has been fighting its own track for years, and control boards that have seen voltage spikes from the property’s power feed. What pulls it down: a single failed component with the rest of the system healthy. This is where brand knowledge matters. A DoorKing board and a Mighty Mule board behave nothing alike, and a technician who has worked on both finds the fault faster than one who has to start from scratch.
For a deeper look at how we handle each system, see our gate repair service page.
What Affects Gate Repair Pricing in Arleta
Arleta is a neighborhood of single-family homes on real lots, and most of the automated gates we’re called to are driveway gates that run every day. That daily cycle is what breaks things, and it’s also what makes the diagnosis straightforward for a specialist. Here’s what moves the number.
- Brand and part availability. A LiftMaster or Linear part is usually in the van or the local supply chain. A FAAC or BFT part for a commercial arm might need to be ordered, which changes the labor and timeline. We work across all nine brands, so we can tell you up front which parts are easy and which are not.
- Gate weight and material. A lightweight aluminum residential gate with a Mighty Mule or Ghost Controls arm is a very different job from a heavy steel or wrought-iron gate on a commercial operator. Heavier panels need heavier operators, heavier hinges and heavier labor.
- Whether the gate is out of alignment. A gate that’s dropped or dragging puts load on the motor every cycle. Fixing the hinge or track problem first is cheaper than replacing operators every few years.
- Wiring and power. Low-voltage control wiring degrades from sun and rodent damage in Valley yards. If the fault is in the wiring, the labor is diagnosis, not parts. We check the whole circuit rather than swapping the board and hoping.
- Residential versus commercial. A property manager’s automatic gate at a small commercial lot needs the same brand knowledge but a heavier-duty operator and a longer service call. Commercial pricing reflects that.
- Age and service history. A system that’s had regular attention needs less work than one that’s been limping for years. If you’re unsure what’s been done on your gate, we can tell you what we see and what we’d do next.
How to Save on Gate Repair
The single biggest way to save on gate repair is to catch the problem while it’s still small. A sensor that needs adjustment is a $145 to $325 visit. A gate that drags on a misaligned track for two years is a motor and a control board. Both get fixed, one is much cheaper.
- Get the diagnosis right the first time. Brand-specific knowledge is the cheapest tool in the box. A technician who recognizes your operator from the housing and the model plate spends time fixing, not guessing.
- Fix the gate, not just the symptom. If the hinge is worn and the motor keeps stalling, fixing the hinge first is the lower-cost path.
- Bundle related work into one visit. Sensor adjustment plus hinge realignment on the same trip costs less than two trips.
- Ask for a written estimate before work starts. Ours is free, and it sets the price. No surprises when the job is done.
- Consider repair versus replacement honestly. On an older system, sometimes a new operator is the cheaper long-term answer. We’ll tell you when that’s the case and quote both options.
Call (855) 473-3106 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Is it cheaper to repair a gate operator or replace it?
Repair is usually cheaper if the operator is under about 10 years old and the fault is a single component. A control board or motor repair runs $325 to $850, against $750 to $1,900 for a full residential replacement. If the operator is older, or if it’s failed twice in recent memory, replacement is often the better value. We’ll quote both on the same estimate so you can decide with the numbers in front of you. Call (855) 473-3106 to get that estimate rolling.
How long does gate repair take in Arleta?
Most residential gate repairs take one to three hours on site. Sensors, remotes and hinge work are usually under an hour and a half. Control board and motor work take longer because we test the whole system before we leave. If a part needs ordering, the timeline varies and the estimate will say so. We dispatch from 7am to 7pm, Sunday through Friday.
Do you work on my gate brand?
Yes, if it’s one of the nine we cover: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite or Mighty Mule. That covers most residential and commercial operators in Arleta. Tell us the brand and model over the phone and we’ll tell you what typically fails on that unit and what a likely range looks like. For more on our overall approach, visit Gate Repair Arleta.
Can you handle commercial gate repair in Arleta?
Yes. Commercial operators, including FAAC, BFT and DoorKing, are a named specialty. Commercial gate repair pricing typically starts around $1,200 and scales from there depending on the operator, the gate weight and whether the fault is in the motor, control board or wiring. Property managers can get a written estimate for budget approval before any work is scheduled. Call (855) 473-3106 to set that up.
What does a free estimate cover?
The estimate covers the on-site inspection: we identify the brand and model, test the motor, control board, sensors and wiring, and tell you what needs to happen and what it costs. There’s no service-call fee and no commitment. The written estimate sets the price, and that’s the price. Call (855) 473-3106. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
What Happens When You Call
You reach a person. We ask what brand the gate is, what it’s doing (or not doing), and how the property is laid out. That lets us send the right technician with the right parts on the first visit rather than a generalist who’ll have to come back. From there we schedule the on-site estimate, confirm the problem, and give you a written price. Gate work is our only work, which is why we can tell you over the phone whether your situation sounds like a sensor, a board or a motor.
We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday.
Why a Gate Specialist Makes the Price More Predictable
A general handyman will quote you a range and hope the diagnosis lands in it. A gate specialist quotes you a range based on what the brand and model typically does. That’s the difference between a guess and an estimate. We work across nine manufacturers, from entry-level residential systems like Mighty Mule and Ghost Controls to heavy commercial operators from FAAC, BFT and DoorKing. Same team for installation and repair, no gap between the two.
Gate Repair Arleta has been handling gate repair and electric gate work since 2018. That’s 8 years of focused service in Arleta, and the same brand knowledge applies today.
FAQs – Gate Repair Cost
How much does gate repair cost in Arleta?
Most gate repairs in Arleta run $195 to $850. Simple fixes like remotes and sensors are $85 to $325. Operator replacement runs $750 to $1,900 for residential and $1,200 to $2,800 for commercial. Call (855) 473-3106 for a free estimate. Estimates are free and the written estimate sets the final price.
Is it cheaper to repair or replace a gate operator?
Repair is cheaper when the operator is younger than about 10 years and the fault is a single part. A $325 to $850 repair beats a $750 to $1,900 replacement. When the operator is older or has failed repeatedly, replacement often wins on value. We quote both. Call (855) 473-3106 to get both numbers.
Can you come out today?
Same-day service is often available depending on the schedule and the brand. We dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. Call (855) 473-3106. We answer 24/7. If you call outside dispatch hours, we book you into the next opening.
Do you charge for an estimate?
No. Estimates are free. There’s no service-call fee, no diagnostic fee and no trip charge. We inspect the gate, identify the brand, diagnose the fault and give you a written price before any work starts. Call (855) 473-3106 to schedule.
What brands do you repair?
Nine: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. That covers the residential operators most common in Arleta and the commercial systems property managers rely on. Call (855) 473-3106 and tell us the brand.
For more on our repair work and the systems we handle, our team is ready to help.
Pricing reflects the Arleta market as of 2026. Gate Repair Arleta offers free estimates – call (855) 473-3106.
What Our Customers Say
"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Xavier Freeman"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Diego Flores"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Lisa Brooks