Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Arleta?
Gate parts and welding in Arleta typically run $180 to $450 for a repair-level job, while a full operator replacement with new mounting and wiring lands closer to $650 to $1,400. The parts themselves are often the smaller line on the invoice: the labor of cutting, fitting, and welding a repair that actually holds is what sets the number. Every job here is priced per job from a free written estimate, so the range below tells you what to expect before anyone arrives.
We’re a gate specialist, not a fence or garage-door company that also takes gate calls. That matters for parts and welding because gate hardware is its own world, and the systems on Arleta properties come from a specific set of manufacturers. We work on your brand, and the list is short enough to say out loud: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Nine brands, one specialist team.
Call (855) 473-3106 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Most parts-and-welding repairs in Arleta come in between $180 and $450.
- Welding labor, not the part cost, is usually what drives the total.
- Operator and control-board work is a separate line from metalwork.
- Estimates are free and the written estimate sets the final price.
- We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Parts & Welding Cost Breakdown (2026)
These are typical estimated ranges for the Arleta market in 2026. The final figure on your property depends on the gate type, the condition of the posts and hinges, and whether the operator needs to come off before metalwork starts.
| Line item | Typical estimated range |
|---|---|
| Hinge replacement (per hinge, welded or bolted) | $90 – $180 |
| Roller replacement (slide gates) | $60 – $140 |
| Latch, stop, and striker hardware | $80 – $200 |
| Frame or post crack repair (welding) | $180 – $450 |
| Sagging gate re-alignment and weld-up | $200 – $500 |
| Wheel or track repair (slide gates) | $150 – $400 |
| Operator arm or motor replacement | $350 – $900 |
| Control board or receiver replacement | $250 – $650 |
What pushes a job up the range? Gate type plays the biggest role. A light residential swing gate with Mighty Mule or Ghost Controls hardware is a quicker job than a commercial-grade slide gate running a FAAC, BFT, or DoorKing operator. Condition matters just as much: a single cracked hinge is a small repair, while a gate that has been dragging for months usually needs the frame welded, the track reset, and the hinges replaced together. On automated gates, the operator has to come off before metalwork and go back on afterward, and that extra step is real labor. None of these line items is a fee; the written estimate you get after we look at the gate is the price.
What Affects Gate Parts & Welding Pricing in Arleta
- Gate type and weight. A hollow residential swing gate and a solid steel slide gate are different jobs. The heavier the gate, the more careful the brace, fit, and weld.
- Brand and operator age. Parts availability varies by manufacturer. Current LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems are what we know best, and familiarity shortens the diagnostic step.
- How long the problem has been running. A hinge that started squeaking last month is a small fix. A hinge that has been loose for a year can mean a torn weld, a bent frame, and a hinge that no longer sits square.
- Post and footing condition. Posts that have shifted out of plumb need attention before any weld will hold. Gate posts go to proper footing depth, and if the footing has moved, the metalwork above it will move too.
- Access and clearance. Tight driveways, block walls, and landscaping near the gate change how much setup and handling the job needs on a narrow Arleta street.
- Wiring and controls. If the operator’s wiring or a control board is also failing, that’s a separate line from the welding. We diagnose the motor, control board, wiring, and operator as one system.
Arleta’s weather is gentle on metal compared with harsher climates. Mild winters mean the ground stays workable and posts don’t heave, but long dry stretches and strong sun dry out paint and finish, and that’s where rust starts showing on gates that haven’t been repainted in a decade. If you’re noticing rust at the hinges or along a weld seam, catching it early is cheaper than repairing the frame later. If you want to talk through what you’re seeing, our gate repair in Arleta team can walk you through it, and you can also read more about the area on our Arleta service page.
How to Save on Gate Parts & Welding
There’s no invented discount here, just a few practical ways to keep the invoice down without cutting the job short.
- Get the small repair first. A $90 to $180 hinge replacement today is cheaper than a $200 to $500 frame realignment in a year.
- Address both sides of the gate, not just the broken one. Hinges, rollers, and latches wear in pairs. Replacing one hinge on a gate with two worn hinges means a second visit, and a second visit is more labor.
- Keep the paint up. A coat of paint on the frame and hinges once they start to dull slows rust and keeps welds from becoming the next repair.
- Tell us the brand when you call. Knowing it’s a Linear or a DoorKing before we arrive means we bring the right parts and skip a round trip.
- Ask for a written estimate. Our estimates are free, and the written number is the price. Call (855) 473-3106 to set one up.
Repair or Replace: Which Makes More Sense?
Repair is usually the answer when the gate’s frame and posts are sound and only the hardware or a weld has failed. Replace when the frame is bent in more than one place, the posts have shifted, or the operator is so old that parts no longer exist. A good rule of thumb: if the repair estimate lands above roughly half the cost of a new gate of the same type, replacement is worth pricing alongside it. We install gates as well as repair them, so we can quote both and give you an honest comparison. From installation to long-term repair, one team handles it.
Is Welding a Gate a Same-Day Repair?
Often, yes. Small weld and hinge jobs are frequently done in a single visit when the parts are on the truck. Larger jobs that need a custom-fit frame section or an operator taken off and remounted may need a second trip once the estimate is written. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, is how the work gets scheduled. If you call and the parts aren’t on hand, we’ll tell you the honest timeline rather than promise a same-day job we can’t finish.
Electrical Gate Parts: Why They Cost More Than Metalwork
On an automated gate, the electrical side is where the money adds up. An operator arm, a control board, a receiver, or a length of wiring in a conduit all carry parts costs that plain welding doesn’t. That’s why we treat electric gate repair as a specialty rather than an add-on. We diagnose the motor, control board, wiring, and operator as integrated systems rather than swapping parts at random. When the gate also needs a weld, we do the metalwork and the electrical work under one estimate, which avoids the back-and-forth of a metal shop and an electrical outfit each charging a visit. Because we work across nine competing manufacturers, troubleshooting is based on the actual system, not on loyalty to one product line. Your system, diagnosed correctly the first time.
A word on safety: a gate operator runs on line voltage, and the wiring and control board inside it can shock or injure. A heavy gate panel, especially a slide gate, can crush a hand or worse if it moves unexpectedly. Don’t open the operator housing or disconnect wiring yourself, and don’t weld on a gate that’s still attached to its operator. A trained technician should handle the electrical side and should remove or lock out the operator before any welding begins. If a gate is dragging or falling off its track, keep people clear of it until it’s repaired.
Why Choose Gate Repair Arleta for Parts & Welding?
We’re a gate-only specialist, and we’ve served Arleta since 2018. Our crews work on residential and commercial gates across nine brands, from lightweight residential openers like Mighty Mule and Ghost Controls to heavy-duty operators like FAAC, BFT, and DoorKing. Our familiarity with LiftMaster and Linear covers two of the most widely installed operator brands in homes around here. Because we install and repair, we see the whole life of a gate rather than one broken part on one visit. One specialist team, and it’s the same one on the phone and on the job.
FAQs – Gate Parts & Welding Cost
How much does a gate weld repair cost in Arleta?
Most gate weld repairs in Arleta run $180 to $450, with small hinge or crack welds near the lower end and frame realignment work higher. The final number depends on gate type, condition, and whether the operator has to come off. Call (855) 473-3106 for an exact quote, and estimates are free.
How much do gate hinges cost to replace?
Hinge replacement typically runs $90 to $180 per hinge, welded or bolted. Replacing worn hinges in pairs is usually cheaper than two separate visits. Call (855) 473-3106 and we’ll price the hinges and the labor on one estimate.
Is it cheaper to repair a gate or replace it in Arleta?
Repair usually costs less, especially for a hinge, roller, or single weld repair in the $90 to $500 range, versus a new gate plus installation. Replacement makes more sense when the frame is bent in several places or the posts have shifted. Call (855) 473-3106 and we’ll quote both so you can compare.
How much does an electric gate operator cost to replace?
Operator arm or motor replacement typically runs $350 to $900, and control board or receiver replacement runs $250 to $650. The range depends on the brand and gate type. We work with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Call (855) 473-3106 for a free estimate on your system.
Can you come today for a gate parts or welding repair?
Often, yes, on same-day jobs when the parts are on hand. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday. Call (855) 473-3106 and we’ll book the earliest opening and tell you honestly what fits in one visit.
Contact Us for a Free Estimate
Whether it’s a dragging hinge, a cracked frame, or an operator that won’t respond, we’ll look at the gate and give you a written price before anyone starts work. Our estimates are free and the written estimate sets the final price. Call (855) 473-3106. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Nine brands, one specialist team, and a gate-only focus that keeps the diagnosis honest.
Pricing reflects the Arleta market as of 2026. Gate Repair Arleta offers free estimates – call (855) 473-3106.
What Our Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Ramon Garcia"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Rashad Carter"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Luis Hernandez